For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I'm using DK as the programmer connected (via Debug Out) to a naked nrf51 module (Rigado BMD-200). I can program it via DK, but RTT doesn't work (no output in J-Link RTT Viewer...
With the new nrf_drv_gpiote, how can I know if the handler has been trigged by event "low to high" or "high to low"?
Please, could you provide a configuration exemple?...
Hello,
I am a beginner. Just bougth a nRF51 DK but have not received it yet.
My second question of the day, very related to my first one, but thoutgh they were different...
Hello, beginner here. :)
I just bought an nRF51 DK, but have not received it yet.
I decided to test it because my older BLE module (HM-11) only allowed me to scan beacons...
Hello.
I installed all of relevant software tools and compiled blinky_example with nRF51822 Dev B/D.
Unluckily, build result is like below.
._build\blinky_arm.axf:...
I have built an application using SD120 v2.1.0. The app runs fines from 0x1d000. When I run an own bootloader (RS485, no need of interrupts or SD120, no pstorage functions...
Hello, My question is that in sleep mode my nrf51822 current consumption is 0.98mA, with only GPIOTE enable, however when I disable it, the current falls to 13uA, but the...
Can anybody explain me step by step how to set an Timer interrupt with blinky LED sample code, since i am new in Coding. I am using nRF51_SDK_8.0.0_5fc2c3a/ timer example...
Hello--
On my Mac OSX system, an nRF51 DK loaded with the HID mouse example doesn't list as a mouse device (no mouse icon listed in the OS) when I start advertising. Instead...
I am working with the BBC on the Microbit project. bluetooth nRF51822 has an ARM Cortex -M4F CPU which is MUCH more powerful than the ARM Cortex M0 being used as CPU. Is it...
Since it appears that version 1.20 is broken and useless, does anyone know where to get an earlier version for 64-bit machines? A co-worker has 1.17 for 32-bit but it refuses...
Hi, I just got my nrf51 DK, I compiled the BLE_URIBeacon example from mbed and downloaded the hex file, 361.2KB. I pushed the RESET button and connected the USB cable to my...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
Hi all,
I tried to implement a software ACK between two NRF24LE1 devices, but failed.
In my tick_interrupt_ISR, I send a frame from device_A to device_B, and I want to...
