I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
I am using GPIOTE interrupts to detect button presses. It works fine but there are only four channels in GPIOTE->EVENTS_IN[] and each channel can only be assigned to...
Hello,
I'm using exeprimental dual mode example with my Beacon kit. I ported the example to work with pca2006, but i'm having problems with led. On my mkit, leds work just...
This is what happens when linking my project in Eclipse:
make all
'Building target: project_name.elf'
'Invoking: Cross ARM C Linker'
arm-none-eabi-gcc -mcpu=cortex...
Hello,
We would like our app to only be seen by:
Devices that have previously connected
Devices that we allow to be added to the whitelist via the temporary disabling...
In my pursuit to make a stable Gazell streaming device, I noticed some issues with pushing packets to the Tx FIFO.
Even through I get an affirmative response from the nrf_gzll_ok_to_add_packet_to_tx_fifo...
Hello,
After I connect my iPhone with a 8001 nordic chip without opening the characteristic I receive a pipe status event which says that the pipe is opened. This is totally...
Hi,
I would like to use the softdevice s130 because i want to try having a nrf58122 as a ble central and peripheral at the same time.
At the moment, there is still the...
Hey everyone,
I have an application where I have to write data to a characteristic. I would like to only allow reliable writes (not unacknowledged ones). Is this permitted...
Hello,
I'm having problems with defining RGB led on my beacon (pca20006). When i define for example RED led (on pin 12) with code nrf_gpio_cfg_output(12); i should be able...
Hello,
I am trying to load ble_app_beacon code provided in nordic sdk to redbear lab's ble nano. I am using sdk version 8.0.0 and soft device(s110) version 6.2.1 .
I am...
If BLE device is sleeping,is link layer connection terminated or the link layer connection is still valid..?
if it is valid..how the master will know about the sleeping periods...
Hi all.
Consumption current increases by about 1.5 mA after a battery check.
uint8_t battery_start(void)
{
// Configure ADC
NRF_ADC->INTENSET = ADC_INTENSET_END_Msk;...
Hi all!
My project is depend on the "ble_app_template",which uses the "scheld structure", I am able to read the data from app but not able to send my data with notification...
