Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi Experts,
I modified a DFU bootloader from SDK 9.0 for nrf51822_xxAA chip. However, I encounter code size overflow problem when building it.
I found the ROM1 configuration...
Here are my 2 scenarios:
I need a radio chip that will be used to form a mesh network in dense bush with each node up to 150m apart. Is this possible?
I need the...
Hi all,
Edit 25 Dec '15: Rewrote post for better readability:
I am trying to modify the dual bank DFU bootloader example to work on our custom board that uses a nRF51822QFAA...
Dears:
I try to use nRF52_SDK_0.9.0_0c82e3e SDK pheripheral pwm example and set the channel1(led2)
duty to 0.
But i still could get the signal about 400mv with LED2...
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
Hello,
I want to add uart debug support to the BLE DFU bootloader (nRF51822, S120, custom board).
Therefor I increased the possible size of the bootloader (start 0x39800...
Good evening and a happy new year to everybody.
Now it's time to work again, and I already stumbled about a little twouble while implementing a peripheral with concurrent...
Hey guys,
I'm designing an antenna for our open source sensor beacon, RuuviTag: http://ruuvi.com
Because we're using 1/4 wavelength monopole antenna, I'm considering...
for ble, scan of central device can get the RSSI value of the advertising device, but the inquire can not.
Is it right?
what's the different between them?
Hi,
I have made custom nrf 51822 board, I don't have LFCLK crystal i.e, 32.768khz. When i run ble_hrs example code in it , current consumption of my board goes to ~150uA...
Hi
In my application I need to transfer several paires of bytes to a slave device, and it's mandatory
for CS signal to go high between pairs. (This actually means I have...
Hi
I want to know why flash memory access should be scheduled in between the protocol radio event?
is there any relation between the flash access and radio opeartion physically...
Hello,
I am developing a wearable device that utilises nRF51822. Right now, I am having a problem because when the wearable device is connected to a new phone, it needs...
Dears,
I am designing a notification application. I would like to know what if I want to support both of iOS and Android phone, which example code of ble_app_alert_notification...
im following ( devzone.nordicsemi.com/.../) step to "Setting up a project for debugging in Eclipse"
i run the debug config and click suspend
then get some problems
...
