But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi guys,
I have a question when design the pcb layout stack with nRF52832, CSP package (CHAA). As recommendation from Nordic, using 4 layers will give best performance...
I noticed that Digi-Key had a new part number for the nRF52 DK that wasn't designated "Preview", so I assumed it might be the final silicon. However, nRFgo Studio identifies...
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello All
I'm newbe for this device. Now my customer asking multiple offline programming IC NRF51822-QFAC-R. But I'm not sure the device can support parallel programming...
Hello,
has anyone done some good testing on the connection quality between multiple nRF51 chipsets running on the S130 SoftDevice? (Using all four connections, 3 as Central...
I'm trying to merge 'ble_app_uart' and 'twi_sensor' example.
I developed twi function in 'twi_sensor' example. I add 'ble_app_uart' example file 'nrf_drv_twi.c'
and also...
nrf51822_sleep.txt
Currently i running nordic code in Arduino IDE through the library from RedbearLab : github.com/.../nRF51822-Arduino and I facing a problem in sleeping...
Hi, can anyone explain to me about this example in this link with details :
github.com/.../main.c
I'm a newbie in nordic and i found it difficult to understand this example...
I install
gcc-arm-none-eabi-4_9-2015q3-20150921-win32
make-3.81
coreutils-5.3.0
and setup the PATH in windows
then i enter CMD mode make some command to...
I am using the LFCLK RC oscillator, 8000ms calibration interval.
Is it possible to read from some register the resulting calibration value for the LFCLK RC oscillator?
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello,
measuring ADC signal on P0.26/AIN0/XL2 and P0.27/AIN1/XL1 doesn't work (I get constant value from the ADC not reflecting actual voltage on the pin). AIN2 - AIN7 seem...
I need to send a disconnect command from the app layer. I've seen a few other posts that say to use uint32_t sd_ble_gap_disconnect. One post had this line of code as an answer...
I am using the RBC mesh in a networking product using the nRF51422. We would like to turn the mesh on and off at selected times, say once per hour for a minute or two. I know...
