I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I have a oneshot app_timer that I'm using as a software watchdog timer. Under normal operation is never supposed to go off. I'm loading the timer with a 15 second timeout...
Hiii,
I am working on the ble_central_and_peripheral program(s130) in sdk8.1.0 .I could connect the device to the MCP and on clicking enable service we gets the notification...
Greetings,
I find it much an arduous task trying to sift through all the SDKs and Documentations in order to find the one specific material that I need. I've installed...
when I use softDevice S110, there exists ble_evt_dispatch function, Can I define event ? if I can, how to define event and how to use event handler . Thank you !
Hi
I want to update the connection parameter and send this request from nrf51822 to a smartphone app. I see there is a function ble_conn_params_change_conn_params() for...
I'm sure there is something obvious that I am missing, but bear with me. The following link references a function called: nrf_drv_gpiote_out_config :
infocenter.nordicsemi...
I'm trying the example in the SDK v0.9.1: examples\spi_master
When I load the project, build it, and debug it, all that happens is that it goes into a failed state where...
I occasionally get an NRF_ERROR_NO_MEM error when trying to add a custom characteristic. I'm only using 3860 bytes of ZI data, stack = 2048, heap = 2048 so it seems like I...
Hi
I am working on the ble_central_and_peripheral example in nRF51_SDK_8.1.0_b6ed55f .In this example it is possible for us to connect to 3 peripherals only.But we would...
Hi, are there any examples in C for how to directly access the registers on the chip? I realize this is a super basic question, but all the register access in the examples...
Hi,guys
I set BLE parameters like this:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL MSEC_TO_UNITS(1000, UNIT_1_25_MS)
#define...
Hi,
I'm using sd_ble_gap_connect to connect to a set of known address and whitelisted devices. My central periodically (once an hour) needs to check on a known set of devices...
Hello,
I'm looking for electrical parameters in nRF52832_OPS_v0.6.pdf but I didn't find typical impedance values for analog inputs .
Also not found any value for RESP and...
Suppose I defined services (According to nAN36 Document)
#define BASE_UUID {}
#define SERVICE1 1602 // This service send a alert message Id i.e. similar to proximity hex...
