Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi everyone,
I am trying to monitor and measure the signal strenth variation by varying the positon of the developement kit NRF51 and i tried with the proximity example...
Hi,
I'm using v1.21 nRFgo. As programming 51series ,
(1)I want to know if the program check the hex file before the log dialog shows "programmed successful"?
(2)And...
I run nRF51 with S110 and advertising at least standard battery service. I can see my device in LightBlue scan window but in iOS Settings->Bluetooth it is not picked up. Which...
i am aiming to design a simple data transfer network. i am using 2 DKs. the first one is the central which runs a modified version of MULtilink Central Example and the seond...
I have continued to build upon the Nordic sdk10:gzll_ack_payload example using gcc-4.9-2015q1 on Linux. The differences are:
added UART for debugging (running at 460800...
Hello Nordevzone, so far, to the best of my knowledge, you can send data using API call sd_ble_gatts_hvx() with "notification packet" (quotemarks due to my limited knowledge...
AS i am trying to utilize GCC for more than 32 KB code size,
i use Eclipse which provides more friendly interface.
However, i am still experiencing some setting issues....
Hi,
Details:
I am using nrf sdk 10.0.0 and s130 Softdevice.I am using nrfgo studio for flashing SD,Application Hex files.I am using this nrfgo studio for past three months...
Hi,
I'm developing nRF51 proximity based device using nRF51822 that acts as BLE peripheral. It advertises continuously using connectable indirect mode.
User has Android...
app: nrf tool uart on iphone 5s
sdk: v8.1.0
softdevice: s110
example: ble_app_uart.
i have modify it based on the answer :
link text
my advertsing init as...
The device I completed has similar RSSI values at approximately zero distance as my development kit; starting with default Tx of 0dBm from the nRF51822 I achieve approximately...
I am having an issue implementing a WS2812b driver for the nrf51422 using the 210 softdevice. We currently have ANT enabled with a tx master only channel setup. The WS2812b...
What I would like to do is run a basic SPI program that reads data from a register on a non Nordic transceiver chip. My nRF51 would have to act as the master because the transceiver...
Hi,
Which service should I use for temperature non-health related, like room temperature, for example? I have browsed trough the Gatt Specification>Services of the Bluetooth...
