Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Hello,
I started with the UART timeslot API but countering some problems.
It will be helpful if I could get any tips or solutions.
I am trying to sample every 2ms and...
Hello
I asked a follow up question on another user's posting on devzone.nordicsemi.com/.../ , but no one seems to respond, so I will try here.
The abovementioned posting...
I've run ble-sniffer_win_1.0.1_1111_Sniffer.exe and pressed CTRL-R, then I get:
Keyboard input error: [Error 2] The system cannot find the file specified..
The log file...
Hello
I am developing an application where the data troughput is very important.
As i understand, the data thoughput is dependent on the connection interval and the number...
Dear developers,
I have a problem with peer manager reporting PM_EVT_ERROR_UNEXPECTED right after it has reported PM_EVT_CONN_SEC_SUCCEEDED.
This is quite a long call...
We all know that PPI can have the same event to trigger other tasks.
But I couldn't find any official document explaining the priorities/timing of those tasks linked to the...
Hi
I am trying to put the nrf52 device to system off state, in order to get minimal current consumption.
When I don't use the soft device, and enter system off state by...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
If i scan again when it is scanning, system goes halt and reset.
So i want to check it's scanning or not before I make it scan...
We have an RFID application, the tag sends the 10 byte data and the data is read at the Receiver continuously thorough SPI channel to MCU.
Payload of 10 bytes, Enable CRC...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello, I want to detect the any activity of the ADXL 362 and blink the LED ON and it should also detect the inactivity to turn OFF the LED.I am able to generate the activity...
Hi,
We are using the Nordic Semi nRF51822-QFAA-T to do BLE project, but when we test CE/FCC RF test(Conducted / Radiated), there has a lot of noise around 2.4G.
BTW...
Hello,
I try to find the information if there is a softdevice (for nrf51 or nrf52) that supports "LE Secure Connection".
In general, where can I find which bluetooth version...
I'm lost.
Can someone point me to place or the best example of how to send data (any) from NRF51882 to iOS app when app is in background.
Is it possible at all ?
I'm trying out the ble_app_gls demo with the Nordic Master Control Panel app (on Android). What I see is that the MCP can connect to the device without bringing up a pairing...
