Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
I have managed to get working a BMW iDrive to act as a bluetooth mouse for my iPhone. To do this I used a CANBUS shield connected to an arduino NANO and an nRF51 BLE connected...
Hello,
Mesh SDK 4.0.0, PCA10040 x2
I want to develop next models:
Scan server: Waiting GET message with arguments, scan BLE beacons and reply STATUS message with results...
Dear Nordic Team:
Now I am doing a example test, with nRF52832 I want to use SPI master and SPI slave transtission.I have saw many demo example,but i dont know that which...
I don't know how it feels if you visit a page that takes six seconds to open.
Isn't the profit ability of the Chinese region enough to allow you to build a normal acceleration...
Hello,
I am working on nRF52832 chip using SDK 15.3.0 in segger embedded studio.
I implemented DFU in my application and it's working properly.
But my problem is when...
WHAT is missing from my profile which prevents me from opening a private ticket?
The location? when I type it in, your profile doesn't save it (it just ignores it).
Ubuntu18...
I have successfully compiled the GPS sample. I am trying to program the device using SES and only beign able to do it when the device is previously erased with NRF Connect...
Hello,
I am using nrf52840 to communicate with PAC 1710 sensor via TWI interface. The nrf52840 is the master device and the PAC chip is the slave device. Without SoftDevice...
I just updated to Segger 4.42a to follow the recommendation in the release notes for SDK v1.2.0
When I do a rebuild the AWS fota sample I get linker errors as shown below...
Hi,
I have a Laird Development Kit for the nRF52840 (DVK-BLL654PA-R2.0) which I want to program. Unfortunately Keil uVision and nRFgo Studio have problems with programming...
Hi all,
Greeting of the day....
Here I am getting an issue with TWI interface. That I am using to communicate with sensor module with NRF52840.
The SCL------> p0...
Hi
I am currently doing a project based on the nRF52840 MCU and evaluation board
as part of my project, I have used the LPComp module, and set it up to trigger on rising...
I have updated to SDK V1.2.0 and the AWS FOTA fails to get an ip address. My version 1.1.0 AWS FOTA still works.
See settings and outcomes below
For v1.2.0
and...
