Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi, Everyone
I am developing with SDK 15.3.0 and nRF52832
Compiling "examples \ secure_bootloader \ pca10040_uart_debug" and "examples \ secure_bootloader \ pca10040_uart...
I can't find anything on this error on Nordic support or Segger support sites. I've looked into the obj directory and only find one main.o file (of course!). Can't see anything...
Hi. We are using a BLE module based on Nordic nRF52832 in a new product we are developing.
The nRF52832 & softdevice has its own QDID - 115277.
However the module also...
I am trying to get a project working with a main.cpp file, some C++ modules, and the 16.0.0 SDK using the IAR compiler. However, using the nrfx/mdk startup files, it never...
Hi,
Iam running the BLE uart and Zigbee light multi protocol example. Using the latest thread and Zigbee SDK v3.2.0. The example is quite good. That the door(Zigbee+BLE...
Hello.
I would like to make simple GPIO bridge. That means transmitter with Digital input and receiver with digital output. When the state of DI changes, it's transferred...
Hi everyone,
I am using nRF52 DK with 52832 on it. My current SDK version is 15.2.0. I know that for IoT applications there is external hardware needed as router like RPi...
Hi,
I have a problem with a specific Zigbee certified device that I can't connect to my Nordic device.
When trying to connect to the device, I go to see the status:
...
Hi,
In need to debug my application using segger IDE when there is bootloader already present in nrf52832 chip .
The sdk we are using is SDK 15.3
Bootloader:- "secure_bootloader_ble_s132_pca10040...
Quick project overview:
Mesh network using nRF52840.
Nodes need to be able to be controlled individually (setting GPIOs) and also report back data (ADC, GPIO state) to...
Dear sir/ madam,
I have two questions regarding NRF52832 as follows:
1. Will nrf52 only get connected to apps provided by nordic? I want to it to get connected to serial...
Hi,
Greetings!
I am using following setup
1. Mesh SDK: 4.0.0
2. SDK 16.0.0.
3. Segger Embedded Studio on Windows 7
I had a look at "pwr_mgmt_pca10040 " example...
I slightly modified the qspi example code to try something that I'd eventually like to implement as part of my application. But when I try to interleave reads and writes then...
Hi,
We did stumble upon an issue with our BLE peripheral running on an nRF52832 with Softdevice S132 5.0.0 . The central side is implemented on top of the UWP (Universal...
Hi. I want to run the pca10059 dongle so that the BLE is in central mode and is recognized as a virtual port on the pc. Is it possible to operate with only UUID settings in...
