SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service with the SIG's PTS device (dongle)
So far encountered a problem with Test Case: BAS/SR/DES...
Just got a nRF5340 DK, testing on macOS 10.15.2. Setup was smooth – the nRF Connect assistant is pretty good. The only feedback would be that an explanation of the "Variables...
Hello Nordic Team,
I'm currently working on a project based on the nRFready desktop. My application requires using the pipes 0-2: pipes 0 and 1 are used in conjunction with...
Hello everyone!
I want to use the app_sdcard to read/write with fatfs on a uSD card in my app which is based on FreeRTOS. While i was implementing this library, i saw that...
Hi,
I would like to know, where the packets are written into the flash for the mesh DFU example.
In nrf_mesh_dfu.c is a function nrf_mesh_dfu_cmd_send:
It calls...
Hello,
I have a little issue during the mesh configuration of my network.
First my provisioner (called master) provision and configure a first node (called slave), this...
I have downloaded project from https://devzone.nordicsemi.com/f/nordic-q-a/55710/while-building-thingysdkv210-on-segger-showing-error-thingysdkv210-source-modules-thingee_ble_handler...
I am using Nordic's nRF52840 DK board.
I wanted to sync time on End Device(nrf52840DK Board) via sending packets to it. What should I do?
what clock/rtc library or API...
I am sorry but this is totally BS. I just got the Thingy 91 and it does only problems...
I have no problem using a full day on getting stuff like that to work, but please...
I am currently developing a device and would like the default behavior at boot to be:
1. Boot up
2. The device should start advertising for non-bonded devices.
3. When...
Using the 15.3 SDK and the 6.1 software device I am successfully changing the transmit power as needed. When not connected and advertising I would like to update the advertised...
hi
i have a problem with 51822.
i test my production, power on /power off again and again.
maybe 51822 can not work. but is too hard happen.
My code is at main output...
I have customized the nrf toolbox app , facing the issues as below
1. I have created two pages , first page is used to scan and connect and second page is used to enter...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I'm working with the ble_peripheral example...
