Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
On our NRF52840 Based product, we have enabled USB CDC Use.
We see increase of ~0.5 mA when enabling USB . We are ok with this , However - when we remove the USB cable...
Hello Nordic Team,
I am creating Scanning application using SES for NRF82532 (SDK 15.3.0 and softDevice 6.1.1), i am using app_timer_freertos timer.
application is calling...
Based on Android studio 3.0, gradle-4.10.1 compile the project downloaded from github.com/.../android-nrf-mesh-library . I get the following error:
The module 'app' is an...
Hi,
I have an external flash ( via QSPI ) working on NRF52840 Based product.
I'd like to redirect all NRF_LOG message to a file , is there a similar log backend available...
Dear developers,
My device uses the NRF52840 SoC and is equipped with a modem for internet access.
To perform firmware upgrade, I imagine I would have to download a DFU...
Hello, I tried to work with nRF52832 to read adxl362 registers, Here is my function to read all 3 received bytes from adxl362 (according to datasheets, the last byte must...
Hi,
I tried to install the latest sniffer v3.0.0 and Wireshark v3.2.0 on my computer. I could not see PCA10056 listed. If I start my wireshark from command line, with "open...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send data from sensor over bluetooth...
When i used Port 0 assigned on Uarte rx tx pin , everything was ok.
But when i changed the rx tx pin to port 1 , for example p1.00,p1.08.p1.09, it doznt work...
i am sure...
I use nrf5_SDK_for_Mesh_v3.2.0_src , nRF5_SDK_15.3.0_59ac345 and board pca10040.
Copy the ble_app_uart_coexist folder into the examples/ble_peripheral folder at your nRF5...
Hello.
I'm doing a DFU customization now.
However, because of the problem of data transmission of the last packet of the first page when advertising,
connection and...
I am setting up a relatively complex project that runs on top of FreeRTOS and it is based on the HRS freertos sample app from SDK 16.0.0. The device will need to run in several...
