Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hello Guys,
I need suggestion regarding the selection of nrf8001 ble module
Does it support OTA updates?
What is communication interface? is it SPI or conventional...
Hi,
I want to discovery all attribute UUIDs as Master Control panel application does. I use API function 'sd_ble_gattc_primary_services_discover' to discovery.
Exactly...
Hi:
I develop my project with gazell, Device can keep send to host,but host can't keep send to device(I'm not mean for host sent ack to device).
In my program, I use "nrf_gzll_add_packet_to_tx_fifo...
In the nRF52 reference design, not using the DC-DC converter would result in higher power consumption. By how much? Any documentation regarding the details. Thanks
Hi all,
I am new in nRF51822. Today I am doing experiment using GPIO and radio transmission.
I wrote a very simple code as below:
int main(void)
{
init_clock();...
Hi, I've got a serious problem in my project. Some of its features require hard timings. The usage time of these features is longer than the single timeslot and I must be...
Hello guys, I'm doing a hobby project and can't seem to get it working. Aim of the project is to transmit temperature values from a DS18B20 using an Arduino Uno and NRF24l01...
I'm experimenting problems with a nRF51822 custom board. Recently I managed to run the blinky sample project. Now I'm trying to test a BLE project, but I'm having problems...
Hey All,
I am currently trying to have a Analog Signal come in through P0.05 which then gets converted via the onboard ADC and send out a Service Characteristic. I am using...
Hi,
I am using your NRF24L01P-R7 part .Can you please specify its maximum distance upto which it can detect other TAG in open area when there is no wind at normal atmospheric...
I have a question about PXP profile. Could I use the nrF52 (S132) Nordic's PXP example to dynamic change TX power when I have bonded or connected Android phone device ? I...
I try to implement a BLE vendor service that has some characteristics. When I bonded the nRF devive (vendor service already download to device) with my Android phone and then...
Hello All,
I have modifies the Spi Master code to communicate with an ADXL345 Accelerometer. I set up my powermode and the percesion in the setup phase. However, when I send...
Hello, Nordic Team.
In my program, I have to change the value of the characteristic before start. I write:
case ACI_EVT_DEVICE_STARTED:
g_aci_state.data_credit_total...
