Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
Hi,
I'm using PCA10028 to communicate with ADS1131 ( www.ti.com/.../ADS1131) which outputs 18bit on SPI bus. I managed to get the data out by reading 24bits, but it feels...
Hello ! When I make a read with the SPI from a sensor's register the data sometimes comes correct and most of the time wrong. I tested the read operation with an Arduino and...
Hi
what is the best way to implement a sleep after disconnect?
We are using a custom board and I implemented it this way:
on connect : turn advertisement off
on disconnect...
I used iar for my project. But for some reason I have to transfer my project to keil now. Attached is the icf file from iar and I also attached my keil settings. Now the system...
In following the example for a DFU BLE upgrade I have configured the following system
on an nRF52 DK install the softdevice and bootloader:
nrfjprog --family nRF52...
In my code, I have some 'print'-style functions that write data to a buffer, and that buffer then goes to the Nordic UART implementation. This is user code, and I don't know...
Hi, I'm trying to adapt the stm32f4 library from:
link text
to run an nrf24l01+ with an stm32f373. After some initial SPI headaches, a lot is working. In the initialisation...
I want to confirm how much current is being drawn from the battery while the nRF52 is in it's absolute lowest power state and waiting for an NFC field to wake it up. From...
I am interested in setting the tx power level the advertising packets in a nRF52832 are transmitted with. I saw there is the TXPOWER register in the RADIO section (address...
I have a use case where sensors on a BLE peripheral need to push notifications to a BLE central indeterministically. So it needs to keep the connection always on. The notification...
Hi,
I tired Nordic Uart Service example on Nexus 5 Android ver 5.1.1, but I am not able to connect. I am able to connect to Samsung S6 and Nexus Android ver 4.4.4. I am using...
Hi Nordic,
I've try many times but no luck, I have a PCA10028, which works fine with SDK8~10 and S110.
Recently I found the SDK has become ver11 and SD turn to S130. So...
What is the best method for sending long data to ble_app_uart from android? We tried sending data by breaking into 20 bytes chunks and used thread.sleep() between each packet...
When I'm using the SDK 6.1.0, the twi drivers works while and I can easily understand the twi work flue. Howeve, the SDK 11.0.0 changed the twi drivers. I don't know what...
