Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Heading ##Here my PCA1000 board is getting detected in nRFgo studio even i can program and debug it, But i cant see COM PORT.
Can anybody help me out in this...
When i...
Hi,
I'm trying out the nRF52832 with kit PCA10040 V 0.9.0. I have S132 softdevice installed and running the ble_app_pwr_profiling example from nRF5 SDK v11.0.0.
I'm...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I am trying to manage the bonds as follows. I've defined the max bonded masters as 4 on my slave. When this list gets full, I delete a random bonded master on the slave (not...
I'm trying to flash to a device with the GCC toolchain using "make -f Makefile flash_softdevice" and nrfjprog fails with the message "ERROR: There is no debugger connected...
Hi.
I've searched this forum and also the code for pin muxings. One of post here said that any gpio can be configured for any output. However how is this done in code?...
I have a peripheral device based on the nRF51822, s130 and SDK 11.0.0. It's designed to only ever have one central device to which it's bonded. Out of the box, without a bond...
Hello.
I have a question.
I want to use UART without flow control.
In this case, I don't know what to set rts_pin_no and cts_pin_no of app_uart_comm_params_t.
Please...
I use nrf51822qfaa,s110,v8.0.
now i use the TWI master.the nrf_drv_twi_tx function always return 0x03(NRF_ERROR_INTERNAL),WHY?WHO can help me?
code:
nrf_drv_twi_t twi_instance...
Hi all:
I refer the "IoT_SDK_step_by_step.pdf" to setup my raspberry_pi ,then I can successfully ping the DK_board from raspberry_pi.
my question is , I can't ping the...
Hi everyone!!
I've gotten the ipv6_coap_server example to run on the nRF51-DK,and I use raspberry pi as gateway and I can got the bt0 interface after connecting to the...
I would like to add LIN-bus to a project of mine.
The hardware part is easy, connect a LIN interface ASIC to the UART of the nRF5x.
But writing my own LIN-bus SW driver...
