nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
hi,guys
For testing the comunication between BLE+timeslot device and radio device, I change the code as below:
void start_timer(void)
{
NRF_TIMER0->TASKS_STOP = 1;...
Dear Nordic,
Whats wrong with the below code. It works well in RFduino but when I try to port the same code in Keil environment.Its not working throwing error as
1.identifier...
I just got a new target board back from fab/assembly and I'm trying to use the debug out connector on the PCA10028 to program the new target.
My target is the NRF51822...
Is there a beginners guide on how to get a console output working for the following setup?
keil v5 & SDK 6.1
nrf51-dk connected with the
TC2030-MCP-NL to a
nrf51822...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hello,
I am new to working with nrf52 and was looking for a way to make printf work in a blank project that I have created. I followed the uart example for the peripheral...
Hi
Now I'm using the pstorage module to save some data.But I meet some problem,I hope I can get your help,thanks a lot.
It seems that the block has been created successfully...
Hello everyone
i am trying to run the pwm library exmaple from github into the SDK VERSION 9.0 but it is showing lot of errors like
............\components\drivers_nrf...
Hello,
I am working on S110 SDK 9.0 and softdevice 8.0 on EK board. I am able to authenticate the connection using static passkey.
I need the information about encrypting...
A LOT of great information is presented by the engineers. Is it possible to post videos of the presentations?
Apple does this for the WWDC sessions. I find myself watching...
Hello Everyone,
i ahve been working on NRF51 series for past two months but suddenly i came to know about NRF52 series the apckage is ame and proce also not varying much...
Hello,
Now I am using nrf51822 with PCA10004 EK board. And the custom board we are using is BL600-SA module. As BL600 can be used with nrf SDK and softdevice, Can I use...
I have a Bluetooth LE dongle and I have also a BLE device that I want to communicate with.
On the BLE device there are a several services like Cycle Power (0x1818) and Device...
I'm using the Ulink-ME tool in order to program/debug my custom board based on the nRF51822 device. The problem I have is that sometimes the flashing procedure is working...
