The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
I'm a hardware/beginning software guy just getting the nRF52 up and running using the Keil uVision5 tools. I go to debug either the blinky project or heartrate project and...
I'm planning on testing an rf link with just a pair of NRF24L01+. Having battled with the PTX side and got that working i'm looking at pipes an addresses.
An answer to...
Hi,
Since version v1.16, nRFGo Studio don't start.
The installation is correctly done, but when I launch software nothing occured. I can see it briefly in process list....
The GCC linker scripts included with the nRF51822 SDK (checked: 6.0.0 and 6.1.0 as well as nrf51-pure-gcc-setup ) include .init_array sections , but do not specify them as...
Why does the soft device raise a SWI2 interrupt to indicate to the application that an event occurred? In the SDK, callbacks are implemented using function pointers. A function...
Hi!
I'm launching code from example to NUS (ble_app_uart) on nRF52-DK. Everything is going OK, except when I quickly send 4 packets in row from UART to connected Bluetooth...
Hi,
I'm currently working on the project with some hard-timing dependent features. As I've mentioned in another topic, it fails if I have advertising turned on. Turning...
Hi, after I updated my MAC OS X to the latest version EI Capitan, I found my JLink commander cannot connect to the PCA10001 board again even with the Jlink commander updated...
I read somewhere that to get the callback working on pstorage write, read etc, you need to call pstorage_sys_event_handler() in a function set by softdevice_sys_evt_handler_set...
Hi,
Each Gazell device has unique address identifier (i.e. base address + prefix) mapped for each pipe. How about the host?
For example:
Device that transmits on pipe...
Hi,
Each Gazell Device has an unique address identifier (base address + prefixes), what is the default address identifier for the HOST?
For example
Gazell device transmits...
Hi,
I'm having trouble with how to begin debugging a hard fault error in my code. When I run the debugger, it always ends in the HardFault_Handler in arm_startup_nrf51.s...
I am developing a project by employing nRF51822 and my code is based on ble_app_uart. I met an issue that if there is no device connects to nRF51800 in 3 minutes, the program...
The nrf51 ARM Cortex-M0 processors, according to the documentation, are "code compatible with Cortex-M3". Does this mean they implement LDREX/STREX instructions for atomic...
