Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
Hello,
I have a collegues Macbook here that constantly connects to my mesh. Has this behaviour changed with the newest version of OSX? Has anybody noticed? I am advertising...
Hello Forum,
I have purchased an nRF52 Preview Development Kit and has successfully tested the blinky and the Hart Rate Simulator.
The document "Product Brief" from Nordic...
Hi,
I am trying BLE multilink central example from SDK9 on PCA10028 board, but everytime device gets stuck at LEDS_CONFIGURE() in main.c.
Below is my setup:
Flash...
Is there any way to stream the BLE data from nrf52 preview development kit to a PC/MAC? I saw this app devzone.nordicsemi.com/.../ but it doesnt work with nrf52.
Can anyone...
just i want to connect PC by normal BLE dongle.
i am using window8.1. and my nrf51822 chip using
ble_app_uart... i can communicate with smart phone but
on my PC, just i...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,all. i use ble sniffer to capture data between my phone and device,that sniffer says:malformed packed and connect failure.What's wrong?
连接不上问题抓包01.png
Hi
I've noticed that the Generic Attribute Service in profile code developed with S110 is missing the READ property on the Service Changed characteristic. It has INDICATE...
Hi, I want to logg faults on my system so in the app_error_handler I want to store some data to flash. This location in flash is erased earlier when no error was present so...
Hi,
I would like to know the time it takes to send the three advertising messages in one advertising period (on channel 37,38,39). What is it? How do I measure it?
Can anyone post this file, or a link to it? I don't have Keil(using GCC with Eclipse) so I appear to be unable to intall the pack that contains this. I am trying to get the...
I want to use timer0 to get exact time delay (without soft device used).
Timer0 configuration is as
void timer0_initialization(void)
{
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;...
Hi,
At present time I perform many tests with power level and link stability. And noticed that if cover nRF base device with hand or put into pocket the disconnection with...
Hello,
Is there any way to configure the flash data default values during programming phase with Keil IDE?
In IAR, it is possible using a file ".s43" included in the...
Hello, I'm using the nRF51822_QFAA chip on a custom board, but the layout and parts are the same as on the nRF51822 USB dongle . I tried flashing the Board\pca10001\s110\ble_app_hrs...
