Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi!
I'm launching code from example to NUS (ble_app_uart) on nRF52-DK. Everything is going OK, except when I quickly send 4 packets in row from UART to connected Bluetooth...
Hi,
I'm currently working on the project with some hard-timing dependent features. As I've mentioned in another topic, it fails if I have advertising turned on. Turning...
Hi, after I updated my MAC OS X to the latest version EI Capitan, I found my JLink commander cannot connect to the PCA10001 board again even with the Jlink commander updated...
I read somewhere that to get the callback working on pstorage write, read etc, you need to call pstorage_sys_event_handler() in a function set by softdevice_sys_evt_handler_set...
Hi,
Each Gazell device has unique address identifier (i.e. base address + prefix) mapped for each pipe. How about the host?
For example:
Device that transmits on pipe...
Hi,
Each Gazell Device has an unique address identifier (base address + prefixes), what is the default address identifier for the HOST?
For example
Gazell device transmits...
Hi,
I'm having trouble with how to begin debugging a hard fault error in my code. When I run the debugger, it always ends in the HardFault_Handler in arm_startup_nrf51.s...
I am developing a project by employing nRF51822 and my code is based on ble_app_uart. I met an issue that if there is no device connects to nRF51800 in 3 minutes, the program...
The nrf51 ARM Cortex-M0 processors, according to the documentation, are "code compatible with Cortex-M3". Does this mean they implement LDREX/STREX instructions for atomic...
Hei,
We would be using nrf52 chip in a very miniature device that should have both BLE and NFC capability. NFC is needed for just as a tag. Thus, nrf52 is a good option....
I moved from SDK 7 to SDK 9. I'm using timers with SDK7
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE, true);
err_code = app_timer_create...
I work with the IAR Workbench and the nRF52 and would like to enable the floating point unit. After installation of the MDK-8.1.0 and the check of the nrf52832_xxaa.i79 file...
Not able to access the corresponding On characteristic if having more than 1 service having this.
Noticed that the app always write to the last On characteristic instance...
I donwloaded and executed the nrf52 examples with Keil µVision as I use it everyday.
The problem is when I compile and use a BLE example, it is stuck in SVC handler.
The...
