Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi Team,
My application is based on nrf51822 SoC in which I am using
BLE and UART interfaces.
There is single UART available and I have used it in communicating with...
Hello,
I am using am using sd_ble_evt_get and sd_app_evt_wait in an endless loop for handling all incoming events.
If I block this loop from executing, I'd expect that...
Hi all
I'm struggling with the easyDMA UART of nrf52. I've got a preview nrf52-DK here where I wanted to make a simple example with the following code but I never reach...
I'm doing a custom board with a nRF51822 FAAG0. I have in it the ST BAL-NRF01D3, with a 0.8pF capacitor.
In the forum I read in a post that some versions of the nRF51822...
Hi everyone,
I am using the nRF51 SDK 10.0.
The documentation for the Debug Logger API suggests sample code like:
uint32_t retval; // Initialize module
retval = app_trace_init...
I want to use the J-link to program the nRF51822 via SWDIO and SWDCLK, every time I click the
"nrf51 programming", the studio stops working immediately, PLZ help, thans
I'm trying to set up communication between an nrf51422, and an nrf24l01+.
The nrf51 is supposed to be the PTX device, and the nrf24 the PRX device.
Communication from PRX...
I was learning GPIOTE using the example provided in SDK 9.0.0. (examples\peripheral\gpiote). The example only uses GPIOTE task and a timer to drive the task through PPI. ...
We have created a firmware and encrypted it with a private key and made it public. When we download it to the chip it's decrypted with a public key stored in the chip. Right...
I have about 200-300 sensors, each requiring to send data at around 0.5-1Kbps to a central node (coordinator/master node), what will be the network configuration/topology...
In SDK 8 for the nrf51422, notifications are always being sent as 20 bytes, regardless of p_len. The BLE_EVT_TX_COMPLETE event stores the proper number in tx_length, but the...
Hi everybody.
I am making an application which combine ANCS and UART on PC100028 (nrf51 SDK 9.0.0). This program worked properly. However when I add DFU service (dfu_dual_bank...
I am currently using Nordic's UART code and wish to build to use the UARTE rather than the legacy UART. I am currently using the following definitions in nrf_drv_config.h...
