NRF54L15 with 3 shared spi devices, not working.
I have a custom NRF54L15 based board with 3 spi devices, all sharing the same SCK / MISO / MOSI lines.
SCK = P2.06 MISO...
Hi,
I have a couple of questions on migrating from Partition Manager to Devicetree since a particular example was not provided. Following the procedure in the SDK v3.3.0...
Greetings,
Although multi-NUS is not officially a sample in the nRF Connect SDK, it is closely related to nrf/samples/bluetooth/central_uart, and I thought it would be...
I have tried several code samples: nrf/samples/bluetooth/peripheral_uart and nrf/samples/openthread/cli. If I set hw-flow-control in zephyr/boards/nordic/nrf9160dk/nrf9160dk_nrf52840...
We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
HI:
I try use pstorage_raw_mode to store data. According to the document description,first steps:
ble_stack_init() and scheduler_init(). Then, in turn, calls the function...
Hello,
I need a FIFO buffer for at least 20 arrays with 8 int32 in each... for use in an algorithm.. is there a more elegant way than just copying them all around each...
I'm using the mbed platform and have been battling hard faults as I try to find the best way to write with high frequency to SPI to update a series of LEDs while still allowing...
I'm migrating an old (but working) app from the S110 5.2.1 (SDK 4.X) to the latest SDK9/S110 8.0. I've read the migration doc, and I'm following the examples carefully (specifically...
Hi,
I downloaded latest version of SDK and all examples resented there are for nrf51422.
Can I use those examples for nrf51822?
I'm using ukeil and I can only select nrf51422...
Our chip seems to be running at ~500uA and I'm trying to narrow it down.
I'm doing periodic battery level checks on a timer using the ADC HAL. So at init I call nrf_adc_configure...
I use s110 send notification to s120 in 1 - 1with 7.5ms connect interval,but the data maximum data throughput is only 21.3 /2 kbps.how can i do to raise the throughput???...
i use s110 send notification to s120,and set connect interval with 7.5ms,but in actually the connect interval is 15ms!!I see s120 softdevice specification,s120 as client which...
Hi,here i met an issue that when i set address type in public mode by funtion sd_ble_gap_address_set(),and then the advdata packet data was all zereo.This project was created...
Dear ladies and gentlemen,
There is not much information about the RESET pin in the datasheet. I guess, it doesn't have an internal pull-down resistor, but when I look at...
Hi,
I have a problem configuring readback protection using boot.
It seams that the BOOTLOADER stops when trying to read some information from the softdevice if readback...
HI:
i want to use peripheral and central function.and i can switch it to work peripheral or central state when i need.which stack should i use.s120 or s130.
I am using CMSIS RTOS (RTX) to implement an application for the NRF52 DK. I have found an error in the SVC handler that results in a hard fault when calling a soft device...
