I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi,
I'm trying to connect my nRF51822 PCA100001 development board to a ARM M3 processor via the SPI. In this case the ARM M3 is the SPI master and the nRF51822 is the SPI...
Hi,
I am having a nRF51 DK(PCA10028) development kit. I am trying to run blinky example on this development kit using Eclipse+GCC environment. I am following nAN-29 application...
Hi, I'm trying to locate the Softdevice whitepaper (nWP-20), the S210 softdevice specification makes reference to it, but I can't seem to locate it anywhere on the nordic...
Hello Everyone ,
I want to use pstorage for my project.i get the example code from here
devzone.nordicsemi.com/.../
and its working properly(i.e read and write operation...
I am using nrf51822, after establishing connection between master and slave, circuit needs only tx antenna, is there any way to put rx in sleep mode for ble application? During...
I have some nRF51822 MBED kits and I want to use them for BLE for both peripheral and central roles. I understand that this is possible with the S130 SD and the Nordic SDK...
Hi, this question could be ridiculous question due to my lack of data structure knowledge.
As you see in the HID keyboard example (SDK 7.2), there are several buffers....
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
It took a bit to learn these offsets and configure the keil project for them. Do these need to change now that I want to begin using the OTA bootloader? I'm imagining that...
It's probably a rare bug, but it is still worth noting. I have been debugging this issue for a day.
I am using SDK 6.1 at the moment.
The problem was that Device manager...
Hello everyone, right now i make my own nrf51822 kit. it works good for all sample example when i use minimum current consumption example it shows 4.5uA current, then i erase...
I would like to create a sensor network consisting of up to 17 nodes, I've been collecting a lot of information about means of communication between them and a computer and...
Hi All,
From the data sheet nrf51822 have a aes hw modules which is used bt softdevice s110.
If i disable the pairing key .
Can I use the inbuilt aes module from...
I am using DEVICEID as an identifier (I know it's not necessarily unique) but when I break the two 32-bit numbers out into bytes, I am finding that the three most-significant...
Hi Nordic, I'm following a guide on this link hrm . I was testing the application with Master Control Panel 3.7.1 with my nRF Development Kit PCA10028. I looked up some of...
