Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi folks,
I have been successful in getting sample code compiled using Keil u-vision and MBED and installing it on nrfDK-51. It has become so simple to install apps - all...
Hi everyone,
I successfully compiled and loaded the experimental_ble_app_uart onto my pca10028 board.
I downloaded and installed the nRF toolbox on my nexus 7 tablet....
Hello everybody,
I want to do something very simple: Read some data from my Bluetooth peripheral. I know the UUID of the data I want to read, but I do not know the handle...
Hmm... this should be a simple question. But I haven't found a direct answer yet in the online SDK docs, the ARM NVIC docs, nor in this forum (and have only been confused...
Hi All,
I have a following setup :
The peripheral BLE device is supposed to send **(time critical )**data packets to Central device but the transfer is very rare (Can...
Hi,
I have modified slightly the OTA bootloader sample in SDK6.1 and SoftDevice 7.1.0. After flashing the bootloader code to the nrf51822 it works like charm, I can update...
when i use BLE_GAP_ADV_TYPE_ADV_DIRECT_IND mode,I can see the device advertise (MCP) but i couldn't able to connect with it (advertising_start at BLE_GAP_EVT_TIMEOUT)
i...
Hi,
I'm a beginner with bluetooth.
I'm actually working with nrf 51822 Evaluation board.
I want to realize a transparent mode of communication with your kit. Can you...
I never worked with Cortex M0 before so I wonder how it's possible to jump to correct IRQ handler when I have my own bootloader and application which are using e.g. UART IRQ...
Hi.
Where i can find some information and guidelines to do a good RF PCB with nrf51822?
thank you for your support
EDIT 02/02/2015
Where i can find " nRF51822 Reference...
Hi, I'm using my custom board with NordicSemi nRF51822-QFAA and J-Link.
(Softdevice S110 7.1, SDK 7.2, and using IAR for ARM 7.1)
I was testing the NUS example using...
Hi,
The examples provided seem to indicate that the NRF51822 needs to be attached to an application processor / CPU (e.g. - Raspberry Pi). How much resources (CPU cycles...
hardware:pca1001
software:s120 v2.0.0 sdk 6.1.0
i will get rssi value by connected by s120.so i update the s120 to v2.0.0. but when the app run, an error occur.[APPL...
Hello,
I am using the Sd130 (v0.9 alpha-1) and do experience a reboot with NRF_ERROR_INVALID_STATE.
I start advertising, then use another device to connect to it. After...
