I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm using the MAX9814 electret pre-amp's output as an input to an analog pin of the nRF51822. The MAX9814 has a 1.2V swing at 1.2V DC (so it goes from 0 to 2.4V). VDD for...
Hello,
I have some questions about the DC/DC conversion factor in nRF51822.
In the datasheet nRF51822_PS v3.1, Figure 11 shows the graph about conversion factor...
I would like to change the device name of the nRF51422 trough a mobile device(Android AND iOS ). The name should be stored even when I disconnect the supply.
From a nordic...
Sir,
We designed a prototype card including "rfd22301" containing nrf51822. We will use in mass production directly the nrf51822.
We will use the BT as a transparent UART...
Hi, I try to transmit mp3 or wave file.
and I am using nrf51822. Is it possible?
I know that people usually use the A2DP profile, When they send a music or video
...
I'm running example apps from the SDK on a PCA10028. When debugging in Keil uVision, I find that I can only stop the code once. The second time I try to stop the code I always...
Hey All,
I am working on a project that involves a Redbear Labs Blend as a sensor platform, then transmits the data to a dfrobot Bluno over nRF8001 BLE. I'm still new to...
The release notes for S110 v 8.0.0 say .
The SoftDevice Specification corresponding to this release is the
S110 SoftDevice Specification v2.0.
I can't find...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, I am using nRF51822 to generate two channels PWM to control motors. Softdevice is V5.2.1. But I found the the Blue tooth connection sometimes dead if the PWM frequency...
I would like to create a unit which is intermitting in the master and in the slave role.It should be most of the time "advertising" and waiting for some master to connect...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi all, please I have some questions.
1- When adding a service then a characteristic, this enables the SoftDevice to send BLE events to the application whenever a client...
