Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi guys,
I am trying to create a Dual bank DFU bootloader (BL) program for nRF51822 which will be able to update the SoftDevice and bootloader no matter if the "Enable...
Hi,
Sorry if the answer is obvious but I'm not getting it :-)
I looked at ble_app_uart, more specifically the uart_event_handle function and its interactions with app_uart_fifo...
I want to access an SPI-only sensor device from a Blend Micro.
There is a need to avoid collisions between the two uses of the SPI port for the sensor and the nRF chip...
I just made it to upload the example to the device. I'm new into firmware development btw.
I changed the timeout so the beacon will stop advertising after 120 seconds but...
Hello, I have implemented the code below for my project
based on switching central and peripheral role in S130.
The code works fine on the Devkit PCA10028 but on porting...
In compatibility matrix it is shown that s110 v 7.3.0 is compatible with nrf51422 when using SDK 7.x.x. But when I downloaded s110 v7.3.0 in its name and specification documents...
I tried to build the example project "ble_app_uart" bundled with nRF5 SDK (nRF5_SDK_11.0.0_89a8197) within the MDK-Lite V5.18K. It failed and I got the following messages...
Hi!
I am attempting to flash sdk11 examples onto a QFAB board compiled using arm-gcc over JLINK SWD p20 via the NRF-51DK.
While running make flash, the nrfjprog command...
Hello I found example for dual bank bootloader ("examples\dfu\bootloader\pca10040\dual_bank_ble_s132"). And it works well.
Do you plan also to add a SINGLE bank boot-loader...
hi all,
I am using SDK version 8.
i want to make button as ON and off switch.
REQUIREMENT:
When button is pressed counter should keep on incrementing when i released...
Hello,
I would like to simulate the spreading of a disease using the nrf51822 beacons. My question is if my envisioned project is possible as I'm completly new to nrf51822...
I would need to change a timer into single shot mode. My code is as follows:
static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(MY_SAMPLE_TIMER);
nrf_drv_timer_init...
