I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hi,
Just a small question, as the subject indicates: Is the power consumption for the Radio RX component (per µs) indicated in the Online Power Profiler for connectable...
Every time I try to connect to Android phone (running Android 7) or nrfConnect, it connects the first time. After I restart the nrf52 DK, the host takes a while to reconnect...
Dear Nordic support,
Now, I am using Nrf51822 to build up BLE Mesh network in my project on Keil C. As I found in here, Nordic doesnt support this chip anymore but is there...
When I try to receive data from terminal at that time it can not goes in uart_error_handle() function and data is not received.
Which macros are enabled in sdk_config.h...
As regards the NRF52840, I want to make sure that it is in System Off not Emulated System Off. Hence the device must not be in Debug Interface mode .
I want to retain the...
We're developing a low power communication stack, where every uA counts.
Currently, I have the system running at a few uA higher than expected, which I'm trying to track...
Hi,
We are developping an app using nrf52840. We started with the SDK14.2 and needed to migrate to SDK15.0 in order to use the long range. We are also using a Bootloader...
hi,
i am trying to on/off led on board(light_bulb code) which is controlled by the other board(light_switch code) with a gpio. when gpio is high led should be on and when...
I am using a NRF52832 and i want to burn a HEX bootloader that only jumps to my APP (i have already burned the Softdevice) when i reset it...
Can you help me ?
Hi,
I am trying to get the GPS from my thingy91, but it is not working. I can see that the board has CAT-M1 connection when I press the top button to get the GPS signal...
Hello!
I am trying to upload my compiled code via nRF Connect v2.6.2 to my nRF52832. But in nRF and also in J-Link RTT Viewer v6.46d it doesn't seem to connect properly...
Hello, I'm developing a BLE peripheral + Zigbee Coordinator, starting from ble_zigbee_dynamic_template of nRF5 SDK for Thread and Zigbee v3.1.0. Both applications (BLE and...
Hi,
After using the ibasis data available on the sim card:
- what is the cost per MB of data consumed on the ibasis provider, please ?
- After using the data available...
