This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I use the nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31 with nrf52840-DK.
I'm looking for a way to get the transmit state after I sent a udp packet. I would like...
Hi,
we've been trying to reduce power consumption do I able to connect unused pins to GND directly?
Trace 1,2,3,4 do I able to connect to the GND?
Thanks, in advance...
Hi,
I am the first time programming with nordic and Segger. As I received the Thingy91 I just the getting started assistent to set up the toolchain.
This worked fine so...
I have the following setup, master (Nrf24L01) and several clients (Nrf52840), the clients listen, the master sends a message to one client and switches to listen. When the...
While most of nRF5 DSK modules have conditional compiling, such as
#if NRF_MODULE_ENABLED(BLE_DIS) the components/ble/ble_services/ble_dfu/*.c lack these macros. In my project...
Hello,
I use nRF5_SDK_15.3.0_59ac345 and ble_app_multiperipheral_pca10040_s132 .c code
In that code I integrate the capsense code it's work but after some time it's...
I'm want setting Secure_Bootloader.(IAR compiler, SDK 15.3version)
I followed the following guide but got stuck in Step B.
https://devzone.nordicsemi.com/nordic/nordic...
Hi All,
Can somebody point me to a Buttonless Secure Serial DFU Example from SDK16 or SDK15.3.0 for nRF52840-DK
I would use it with only Rx/Tx that is No Hardware Flow...
I want to read all data from a cluster is there a way to pass a wild card to
ZB_ZCL_GENERAL_ADD_ID_READ_ATTR_REQ(p_cmd, attr_id);
Or is there a smarter way to get the...
My nRF9160 DK is not able to connect to nRFCloud.com. I did the certificate update just in case to no avail. I have made sure to update the modem firmware to 1.01 and I used...
Hello, and thank you for making the nRFX components open-source on GitHub!
Now I realize that it's only been up for a day :smile: but most of the changes are reasonably...
Hi,
I'm moving from the nRF52 DK to using the nRF52832
https://media.digikey.com/pdf/Data%20Sheets/Fanstel%20PDFs/BC832_V2.01_Dec-2017.pdf
It can be hand soldered...
Hi,I have some problems when disable peer manage in ble_app_buttonless_dfu project in sdk15.3.0 on nrf52810.
I disable PEER_MANAGER_ENABLED in config.h and remove the peer...
I want to save encryption state in DFU to the nrf_dfu_settings_t structure. I put a new 16-byte field at the end of the structure after nrf_dfu_adv_name_t adv_name; and whenever...
