Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi all,
I am currently trying turning off the active time, so that the nrf9160 immediately goes in power save mode after RRC Connected Release.
If I send the command ...
I connect VBUS to VDDH, and use a USB cable for power supply(high voltage mode), but I cannot download firmware into the 52840.
Unless I power the 52840 from the VDD pin...
Hello,
I'm a teacher. I use the microbit card that loads one of your components. Nordic nRF51822-QFAA-R rev 3 Could you tell me if this processor is based on a Von Neumann...
Hello, just a few quick short questions regarding nrf52 devices:
Do I have to configure and initialize them before using?
Which function should I use? I...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Issue-background...
Hello,
nRF52840-DK
SDK 15.3.0
SoftDevice: s140
IDE: SES
Example: Flash_fstorage_s140_pca10056
I do not read back the expected value in the example. The terminal...
Hi, I am trying to do DFU OTA. I am using SDK v16.0, s140_nrf52_7.0.1_softdevice.hex, SES and nRF52840 dev kit. I am finished with my application and it functions as expected...
Hi,
We are a module manufacturer. We are making modules based on WLCSP, QFN based nRF52840 SoC.
Can you please provide software(preferably GUI) available for module FCC...
Hi guys, i can't figure out how to create an event handler in my Mesh Client.
The functionality of this handler should be to set a flag on the 'NRF_MESH_EVT_TX_COMPLETE...
I used keil v4 compile the following project F:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_uart\pca10040\s112\arm4\_build get file nrf52832_xxaa.hex of size 101kb...
Hello ...
I'm porting our product from RF Digital's Simblee to Laird's BL651 (nRF52810). A phototransistor measures light, is connected to an analog pin, and is sampled...
Hello guys! And girls
My project is working as expected in SDK14.2. I'm updating adv data (manuf. spec. data) without any problem with this function But in SDK15 the function...
Hello,
I'm working on a project using a Thread network to send MQTT packets and I'm having an issue with the example project out of the box. I'm running the version 3.2...
Hi, Sir:
I am developing nRF9160 DK(pca10090) with mqtt_simple example in nRF Connect SDK(ncs/nrf/samples/nrf9160/mqtt_simple). Firstly build the example , build OK, but...
