Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
Hi,
I am working on a project where I need to send and receive ASCII strings from my Central Device to the Peripheral Device. Before the communication starts there should...
Hi, we have an nRF9160DK (0.8.3) and it does not connect to the nrfcloud.
We have updated to the latest firmware 1.0.0
We only have nb-iot here so we didn't use the iBasis...
Hi Guys
I need your advice. I have a customer that is currently in production with the NRF52840 . They now require direction finding but need a Nordic Evaluation kit to...
Hello,
I am new to Nordic platform, previously i had worked on TI controller.
I have three questions to ask:
1) My firmware consists of four services, each service...
hi,
I am using nRF52832 with KEIL. I want to use version6.0.0 softdevice, but I can't select from KEIL runtime library.
Also, the version that can be downloaded from...
I am trying to change after 10 seconds into non-connectable mode. I am using the below code for initializing:
I want to change mode into non-connectable using this type...
When I use dfu_nrf52832_xxAA_s132_6.1.1.hex, it works all devices updated with blink code as described in dfu_quick_start.md But without any provisioning Process, why? And...
Firstly , I have 2 phone. Phone A is huwawei using android 7 and Phone B xiaomi pocophone using android 9.
Phone A already success connect using UART. But I want to try...
I have a same question:
https://devzone.nordicsemi.com/f/nordic-q-a/22025/in-nrf52840-not-able-to-program-boot-loader-hex-is-using-nrfgo-studio/86420#86420
But I not working...
Hi, I am trying to run the following demo here: https://github.com/NordicPlayground/nRF52-ble-long-range-demo
I have followed the instructions and copied the demo folders...
In my understanding, only Nordic NRF Connect (Android and iOS) can be used to bootload a device using the Nordic DFU.
Is there a corresponding command line tool to perform...
I followed the issues from https://devzone.nordicsemi.com/f/nordic-q-a/54149/error-by-loading-solution-on-ses, which fixed the zephyr script issues, but was seeing the same...
Hi,
I have migrate to SDK14.2 the MPU9250 exemple from the peripheral folder in the nrf52-pesky exemples : https://github.com/e27182/nRF52832_pesky https://github.com/e27182...
I am using the nRF52840 DK with the s140 softdevice and am trying to copy the interrupt vector table to RAM to modify interrupts during run time.
I run the following function...
