Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
We have an nRF52 DK system running ble_app_uart_c example code and communicating with a peripheral device. We setup a second development system using another nRF52 DK system...
I have the nRF52840-DK with the adafruit PN532 RFID/NFC shield installed on top of it.
I run the TWI Scanner and receive a report that a device was found at address 0x24...
I am having a strange issue with my custom radio protocol. I have ported the code to the 52840 and SDK15 from the nrf51822 where it is running with no issues.
The issue...
Hello,
I have PCA10040 development board with nRF52832, Softdevice S132 v6.1.0 & SDK 15.1.0). I wanted to use the extended advertisement feature to advertise more than 255...
Hi,
After developing two application, one for emitting extended advertising and other one for scanning this kind of advertising on nRF52840 DK (Github repository here: MOTAM...
Hi,
I would like to ask two questions.
1)
I understand that the nrf52832 does not support the feature "Transmitter has a Stable Modulation Index".
But the component...
Hello, I am trying to build the asset tracker reference app for my newly acquired Thingy:91.
I went through the instructions to get the toolchain and SEGGER IDE up and...
Hello,
We are currently using a Raytac SoM that has nRF51822 SoC with Adafruit UART firmware. We are running into two different scenarios BLE connectivity issues where the...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
After Christmas update we are unable to use DFU from Android devices.
We've been using such function on a regular basis with our devices and everything has always been fine...
Hello everyone,
I'm using a NRF51822 as a central device, I connect to a peripheral (NRF51822-based device), then I stop the scan. At a later time I initiate another scan...
Hi,
I am trying to program nRF52832 custom circuit with nRF52 DK, I have connected debug out from the nRF52 DK to the custom circuit containing nRF52832 debug in. When I...
Hey Guys,
i am currently experimenting with the NFC functionality and have an issue with our "nrf52840-DK" boards:
i am testing with IAR (8.40.2 - including the library...
Hi there,
I'm trying to use serial library from SDK to interact with cellular modem (AT commands, not nRF9160). I've read documentation (library description, api). May be...
