Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello,
i'm using,BMD-301(NRF52832),SDK15.3.0
////////////////////////.......Issue-1..............
When i upload "twi_master_using_nrf_twi_mngr" peripheral example...
Hi, I'm developing a Zigbee coordinator starting from CLI agent example on nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31. The end node I tried to connect is Ikea TRADFRI ambience...
I2s subcontract transmission, the sound is normal during the transmission of each packet, and there is noise when preparing next_buf. How to eliminate the noise? Looking forward...
Hello Community,
I want to request a timeslot with sd_radio_session_open(). Whenever i call this API function, the Application crashes with a HardFault.
I have no idea...
Hi Devzone!
I'm using 'nRF52840' as an edge device, and this device is going to continuously check the surrounding environment and send the value to mqtt broker of aws through...
Hi,
We are using nRF52832 with a custom protocol communication (not BLE, not Nordic). The communication is simple, one device is sending message and the other is receiving...
Once again I'm turning to this forum for help, as I'm stuck with an unusual issue. We have a custom board, which is supplied from one CR2032 battery and can also be suplied...
Hello,
I am having an odd issue when loading an app that uses FDS with softdevice, if I load the app without a bootloader the FDS library seems to work just fine but if...
on connection, the modem gets reset after ~ 1 minute from activation:
log:
[00:00:00.421,386] <dbg> nrf_cloud_transport.nct_topics_populate: shadow_get_topic: $aws/things...
I would like to implement functionality to use a digital temperature sensor TSYS01. I cannot find that this already is implemented in Zephyr so im wondering how i in best...
Hi there,
I want to use a LiFePO4 Cell to supply the nRF9160:
Is the MAX17224 suitable to power the nRF9160?
Is this Power "Sequence" OK? Productspecification nRF9160...
currently we are facing an issue with our testing that, our product battery is getting drained to 0 volts. we understand that we need to put a cutoff voltage from the firmware...
Hey folks,
I'm developing a long-range application with nRF52840 DK that (optionally) uses NUS (Nordic UART Service) to send data to Samsung S10+; there is no problem establishing...
Hello,
SDK 15.3.0
nRF52840-DK
s140
IDE:SES
I am running into an issue using the app timer and LPComp together. The error is NRF_FAULT_ID_SDK_ERROR, With RTT output...
Let say during the normal program flow I want to change often the edge direction which will trigger the event: rising edge, none, falling edge, none … Can I work direct with...
