Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi, I can read data with my laptop BLE as below.
Could anyone tell me where can I find the data layout doc? I want to figure out the data layout and dimension.
Thanks...
I've been having several issues with the nRF52840 so far:
Issue 1:
When trying to flash an nRF52840 with NCP firmware using a Segger JLink, I connected the SWDIO and...
Hi all,
I noticed an issue on the last release of the NRF Connect mobile app at least on Adroid devices.
It seems that every time I am trying to make a secure DFU (buttonless...
Hey everyone!
How often does PM write into FDS? On each connection? Or on each new bonding? PM has some kind of peer ranking so I suppose that it needs to write on each...
Hi Nordic Forum! I'm currently developing a CLI controlled BLE scanner using the nRF52840 Dongle. Essentially I brought over the CLI example and adapted it to the a central...
Hi
it looks like the Publication Retransmit Count and Interval states default to 1 time and 100ms respectively. Is there a reason these defaults apply? I don't think it...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available. After a few minutes it sometimes changes...
I would like to program the 52840 with the HCI_UART sample to use it for Bluetooth scanning. I did this and lost the USB serial out. I now understand that on the Thingy91...
Hello,
I am evaluating the nRF52840-DK. I just want to play around with Nordic for awhile to determine if I want to port my current project which is written in C++ for Teensy...
I want to run various applications in some cases
what I want is :
In general, it runs own application.
When external memory(SD card, USB, EEPROM, etc... something...
Hello All,
I have developed advertising init in 14.2 sdk (in segger ide).
(working on nrf52810 board)
I wanted to migrate same functionality to 15.3 sdk so how i can...
Hi everyone! I am using the STM32L4xx Sensortile to transmit accelerometer data from the Sensortile Acceleromter. The characteristics of other functions are shown on the nRF...
Hello guys,
I wan`t to make an project that send trough serial port a new image to flash my nrf9160.
By the moment I managed to send and recieve data but only on uart0...
Hi,
Iam running the BLE uart and zigbee light multi protocol example. Using the latest thread and zigbee SDK v3.2.0. The example is quite good. That the door(zigbee+BLE...
