Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are interested in integrating BT MP3 player in our product and Im wondering if we can use Nordic SoC to stream audio via bluetooth to the Headset? So create an A2DP...
Hello, I am trying to develop a low power application by using nrf51822 EK board.
In " Reference manual v2.0, 11.1.3 System ON mode ",
it says there is a mechanisms can...
I am using app_gpiote_user_register() and ads_interrupt_enable() to define a ping change interrupt. When the code runs, I can see on my logic analyzer that the GPIO pin assigned...
I have a nrf51822 project with S110 (v6.0.0) softdevice. I am using latest sdk (v5.1.0). I compile the project successfully with gcc and it does run too. But I struggle with...
I'm trying to reconcile two things I read about the softdevice. The GAP roles that are supported include broadcaster and peripheral. Also, there is support for a GATT client...
Hello
I am trying to build the nAN-36 application.
The main.c file include at least two files that I do not find:
#include "ble_eval_board_pins.h"
#include "ble_stack_handler...
We're trying to implement initial programming of the chip using SWD. We can connect to the chip and successfully enter debug mode but from that point on (as per section 11...
Hi,
I'm gong to design a pcb for nRF81522 (for both packages: QFN 48 pin and 64 pin WLCSP). I coudn't find the footprint in any documents. I appreciate if anyone can send...
Hi all,
Trying to read out the nRF8001 serial number using the nRF8001 SDK 1.7 and I cant seem to work out where I should be making the call to lib_aci_get_address?
After...
I'm a wireless novice, but have electronics experience.
I'm looking to add bluetooth low energy communication from a battery powered MIDI controller to a Macbook Air (or...
Ole,
I am trying to update the serial number value in an already initialized standard Device ID profile.
[i]dis_init.serial_num_str.length = (uint16_t)strlen(newserial);...
Hi,
We are trying to reuse the RF frontend design provided in reference design of PCA10000-nRF51822 Development Dongle 2_0. But because we have different board thickness...
I'm trying to add another timer to the BLE proximity app sample code in a new source file which is a driver for a GSM modem. My timer handler function is never called.
...
Hello,
How can I synchronize the wireless nodes (one nRF24LE1 on it) in a real-time wireless sensor network? I use nRF24LE1 as the transceiver and receiver.
Thanks.
