Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
I found some examples on dev zone how to read RSSI during connected state:
Function report RSSI but as a positive value around 230. How to recalculate it to dB. I see...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
'm sending a publication set message (0x03) from an iOS app to an nRF52840 board using the light server example in the latest SDK. This works and I'm able to receive messages...
Dear All, I would like to know which is the better GPIO configuration to drive a LED for extremely low power consumption. We have a board with nRF52832 SoC with GPIO connected...
Hi,
I have Android (8.1.0), and installed nRF toolbox 2.8.0. To update firmware using .zip file.
The DFU Upload returns error:
Unfortunately, nRF Toolbox has stopped...
The 3GPP Release 14 introduced new, third power class of 14 dBm for NB-IoT devices. Is it possible to assign nRF9160 to operate at the lowest power rating class, the 14 dBm...
Hello everyone,
I am working on a project where I need to interface an NFC reader (trf7970a from TI) to an NRF52840.
I got everything working fine, but I have a major...
Hello,
I am running S140 on an nRF52840 custom board. While doing some power profiling, I noticed a spike of current of ~15mA when going from sleep mode to waking-up due...
I've created read onle characteristic called "log". In main.c i try to update it by calling : ulogd_characteristic_update(&m_ulog_service,Log_Data_arr)
But nothing happens...
How can delete individual peer bonding data without to affect the rest bonds:
-currently connected (after disconnect)
- some peer by providing RPA (assuming RPA matches...
Hi,
Is it possible to enable the transmission of 2 bytes of preamble and use the TIFS register to force a delay to transmission when in proprietary 2Mbps mode?
Thanks...
Hello, I'm using SDK 16.0, softdevice s132 v7.0.1, I'm sending the device to SystemOFF and configuring a pin to wake it up with
nrf_gpio_cfg_sense_set( IMU_INT2_PIN , NRF_GPIO_PIN_SENSE_HIGH...
Hi,
I am using a 52832 part as a peripheral communicating with a central running on an ESP32. It operates in the following manner:
1. When it is active, the peripheral...
I am getting a "Stopped by vector catch". This isn't particularly informative. How does one find the code location where the fault is generated?
Thanks
Hello everyone,
I just started learning BLE. I want to develop an application that gets RSSI from a beacon and displays the magnitude of RSSI using 4 built-in LEDs.
Beacon...
We want realize mesh network to mibile phone clients using BLE5
We assume we are have to use 3 types of devices:
1) Mobile phone/pad with built-in BLE5
2) Access points...
