Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I haven't seen any posts about this, so I thought I'd post what I observed and how I fixed it in the hope this helps someone else.
My nRF51 DK (PCA10028 v1.1.0) out of...
I have gone through most of the guides/links that I saw here to no end.
My development environment is OS X 10.9, gcc-arm 4.9, nRF51822 beacon.
Before going for the IDE...
Hi,
I am trying to build a low power device using the nRF51422 SoC without a Soft Device. I need a timer to occasionally wake up the chip and as I read the product specification...
I have a basic question regarding a basic area. Interrupts! But without any good specification and how the OS work and good example how to do this I need to push for the obvious...
In ble_dfu.c (unmodified SDK 8.0.0) I am unable to get the buttonless DFU hooked up.
For reference, ble_app_hrs with s110_with_dfu works correctly. I have traced my issue...
Hello,
I am trying to write data to flash with the pstorage api. I managed successful to write data to flash with the pstorage_test_store_and_update() function from the...
I am searching a cheap wifi solution and this NRF24L01 communicates through 2.4GHz network, therefore it may be compatible with 802.11 protocol and further with TCP/IP protocol...
Hello!
We're using PPI to connect one pin to clear and capture events on Timer2. On pin low-to-high we're clearing the timer and on pin high-to-low, we're capturing the...
Hi,
I am planning to use nRF51822 for one of our projects.
Can you please hlep me with the SDK that will support IAR Embedded Workbench.
Thanks & Regards,
Sumit
Hi,
For SDK 8.0.0 and Softdevice S120.
(1) Maximum number of services supported for db discovery ?
(2) Maximum number of characteristics per service for db discovery...
When i try to add pstorage in Keil 5 packs manager without a softdevice ble_flash is required as additional software component. Adding ble_flash requires a softdevice as additional...
We have a custom board on which we have NRF51822 SOC. We also have a small external flash memory(From Spansion) on our board. I'm trying to figure out the ways to use this...
