Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi ;
If there is a ble message coming , but this time ble is getting data from sensor , what will happen ? Will it device reset ? Would you give me any idea to avoid this...
Dear all,
We have a question.
Did any body tried to make so that Bluetooth Mesh 4.2 works in PARALLEL with Bluetooth 5.
Some schedule reserved for BLE MESH 4.2 and some...
Hello,
I never used BT modules before. I'm going to buy some bluetooth modules to add wireless to an existing board.
I need module with following characteristics:...
Hi，I want to write the firmware to 52832 from android system by UART .I have readed the firmware into bytes, and then do not know how to compose the bytes to write into serial...
I have the following situation:
My device receives a number of RF packets, changes to TX mode, sends some data, goes back to RX mode and it should be able to access the...
Hi,
my application is normally a BLE scanner, listening for beacons. This runs OK.
Now, I tried to add a tested piece of connectable gap/gatt firmware, that runs fine...
Hi ,
in the RTOS example, you set
configTICK_SOURCE as FREERTOS_USE_RTC and configCPU_CLOCK_HZ as( SystemCoreClock ) .Since SystemCoreClock is 64mhz, why did you not set...
I am trying to understand why when I connect the nRF52840 Dongle using nRF Desktop I get this message in the log:
2020-02-26T23:12:13.293Z INFO Connectivity firmware version...
Hi Team,
We are using nRF 52840 chip for our development of product.
As of now the settings for BLE data transfer are as below.
MIN_CONN_INTERVAL 20 // which is the...
Hi,
I'm developing a router Zigbee device starting from light bulb example.
In the example the function zb_set_max_children is called passing 10 as parameter.
About...
Hi,
I am using
PCA10056
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am testing background serial-dfu.(refer to https://devzone...
Hello,
We are working with the nrf 9160 dk.
We need to use internet connectivity to send an http get and post to a remote server.
We want to utilize the NB-IoT...
I've been developing firmware for my PCA10059.
I load the package with nrfutil dfu usb-serial --package=_build/t.zip --serial-number=`cat /tmp/serials.txt` --connect-delay...
