Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Unable to Install or Launch nRFgo Studio Win64 1.18:
Downloaded "nrfgostudio_win-64_1.18.0_installer.msi
Installed package on a 64-bit Windows 7 PC as a 'regular...
I'm playing with the SDK 8.0 HRS peripheral example.
There is a config folder that contains device_manager_cnfg.h. But this isn't being built into the project, the version...
Hello,
I am currently trying to write my frist few lines of code.. I started with the ble_uart example and then mixed in some code from the spi_master example.. I wanted...
Hello,
why did you chose to remove the S130 1.0.0.3-alpha from the relasenotes and merge it with the latest version? I don't think that's the way it works. Now we have...
Hi All !
I was read many posts about this function and do not understand how to check if all data is deleted.
In my situation I do:
Start advertising for bonded...
My devices in the field have firmware that saves an error code when it gets thrown and then sends it to a central so that I can see if there are errors with devices in the...
Hello,
I am using the sd_flash_write function. If I use this function without the nrf_delay_ms() function (see code below) the data is not being written.
sd_flash_write...
I would like to know if it is possible to log realtime sensor data to flash while advertising. I would like to have a device which transmits real time ECG data over ble UART...
Hi
I am struggling to change the device type on examples setup for nrf51422 to nrf51822.
If I change the setting in "options for target"/device I get the failure message...
I changed the multilink central example to some custom code. However, it seems like I've run out of space. But I don't under stand how this is possible because I selected...
Using gcc-arm-none-eabi-4_8-2014q1-20140314
Using nRF51_SDK_8 Using nRF51 dongle
Build in nRF51_SDK_8/examples/peripheral/blinky/pca10031/s110/armgcc succeeds...
Hi there,
When i disconnect the keyboard, the nrf51822 will restart advertising in directed mode.
And then on_adv_evt() will receive BLE_ADV_EVT_PEER_ADDR_REQUEST event...
Hi,
I want to use BLE for following situation and I wonder if it is achievable.
I have a 3 boards with nrf51822. Two of these boards have mpu6050 sensors connected to nrf51822...
Hi,
I am a little confuse at the moment and wondering if anyone would have any insight on the matter.
I am making a pair of device with s110 and s120. So the s120 will...
Hi,
I'm trying to write my own application based on the ble_lbs example on nrf51822. Recently I've discovered a problem with reconnection to the beacon. I can successfully...
