I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
My customer is now unable to disable secure erasure after using the APPROTECT function. Is this correct?
Please let me know if there is another way to check this.
”nrfjprog...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Hi team, We’re using the STM32H7 as the host MCU and the WMC02C Wi-Fi module (based on the nRF7002) connected via SPI on a custom board. I tried running the Wi-Fi scan example...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Hi
We are migrating from Segger Embedded Studio (SES) to VS Code for developing in the nordic connect SDK. We are using the RTT logger for debugging our device. In SES you...
Hi Nordic,
I test with nRF7002-DK and IC mark on nRF7002 is below:
N7002 QFAAB0 2252AA
Here is my test data, showing about a 3dB discrepancy between power setting...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
When I was using the code from the following website, I encountered many errors while creating a new build for compilation。
https://github.com/NordicPlayground/nrf-esl-bluetooth...
Setup: - We have a custom board using the BL654 (Laird Connectivity) module with the NRF52840 core using SDK 17.1
Issue:
- On power up we configure the GPIO 41 as an input...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
