We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hii all,
I wanted to generate a clock pulse from the pin P0.05, I've written the code and when I tested the application with nrf51 DK with chip 51422-AC its working fine...
Hey everyone,
I'm trying to send a value as a notification packet from GATT Server (slave) to GATT client (master) at 7.5 ms connection interval. I have set up the radio...
I am using a simple 4 by 4 matrixed keypad, and I would like to handle some of the decoding myself.
In essence, I would like to configure all 4 rows as low driven output...
Hello,
I already searched the forum, but I didn't find anything.
Is there a way to invert a port on a NRF51822?
I use this chip together with an XMega-Chip and they...
Hi,
I'm trying to get PCA10001 board working. I used ble_app_hrs example from SDK 6.1.0 (I'm using eclipse with gcc). The Softdevice is v7.1.0
The application seems...
I have a nRF51DK with SD 8.0 flashed.
I would like to start and stop a pwm signal with the buttons on the board(BUTTON_1 and BUTTON_2). The pwm is working fine. But when...
Hello:
I want develop my nrf51822 project base on new sdk and softdevice.In /nRF_Examples/9.0.0/ble_periphera/ble_app_uart/, the keil project device is nrf51422,and it can...
Hi,
I'm compiling the simple blinky example with no softdevice for an NRF51822 xxAA using GCC on linux. I can't get any LEDS to blink off the GPIOs, so I'm debugging with...
I can see a phrase "Not recommended " on the Evaluation Kit's page: www.nordicsemi.com/.../nRF51822-Evaluation-Kit
What could that mean for me if I already have the kit...
I found in ble_app_uart example, any device with UART app can connect to uart service and send something to COM port or just block the connection of other devices.
So can...
I'm trying to update my firmware using the dfu, I tested two examples of the SDK :
one of them is dfu_dual_bank_ble project,
I noticed that the memory allocation...
Hello,
I have been reading a lot of Nordic and DevZone stuff. The information I need appears to (almost) be there but I cannot quite put it all together. I need some help...
Hello, I am asking for your help again.
I just managed to brick the chip that I am working with. The problem is that I am not able to erase or program the flash. However...
Hello,
I have not found a lot of information on connection encryption. I want to use a preprogrammed Long Term Key in my mesh that is then used to establish subsequent...
This is the application file I am trying to download:
dx02.zip
This is the sniffer Log I just captured by wireshark
dx02_20150820.pcapng
I was able to upgrade firmware...
