Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hi,
I use NRF51822 as a transmitter in "gazelle mode" so no soft-device is enabled. At the other end I use NRF24LE01 as a receiver. In order to see what is going on in...
Hi All.
I made a nRF51822 based PCB with SWD header but I don't have any J-Link lite to load Firmware.
I have a nRF51822 Eval Kit. Is there any way to use the J-Link of...
Hi,
I am using nRF51822 and I compiled and loaded uart example code. Also i used nRF toolbox android application on samsung s5 with android 4.4.2.I am using sofdevice 6...
Hi All,
I would like to broadcast 256 byte data in one shot every second, any reference in SDK recommend?
Thanks in advance.
**updated at 19 Sep, 2014
Application...
Nordic,
After upgrading to S110 7.0.0 the BLE_LBS example no longer works as downloaded from GitHub. I adjusted the flash algorithm size which fixed the first problem and...
Hi Developers,
I'm using an nRF51822 and finally beginning to understand BLE. I want to learn by example so I downloaded NAN-36.
Im at a point where the Application...
Hello,
i'm using the NRF5182 QFAAG0 chip, its one of the samples from the evaluation kit.
I can program it with keil (not using the S110). Using nrfgo studio i can see...
I'm building a BLE peripheral / observer multi-role application using the timeslot API and based on the example code at github.com/.../nRF51-multi-role-conn-observer-advertiser...
Hi,
this is my first time I write on this forum and I hope to find some useful suggestions for my work on Nordic platform. I work since many months on nRF81522 chip and I...
Hello Everybody,
I'm sorry I'm a little confused about the SDK and S110 versions. Can I use S110 v7.1 with SDK v6.1?
I compiled the ble_app_beacon I found in the SDK...
Is there a way to implement a blocking flash write without dealing with system events. Periodically, every 10 seconds or so, I need to dump a large amount of data to flash...
So I have bought some nRF51822 Beacons to develop with. It was suggested when I purchased them that I wouldn't need any further development kits - but whilst I can see the...
Hi,
When using Master control panel both on PC and my galaxy S3, I can detect and connect to the HID keyboard app, but when trying to scan for Bluetooth devices on Galaxy...
Hi,all!
My question is:
Can one smart phone connects two peripherals(both based on nrf51822) at the same time?
If it can, should the peripherals use s120 softdevice...
