Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
Hi,
We have a hardware application that prevents us from using flow control to interface with external hardware. We require the NRF51822 to be able to buffer up to 256...
I have a working design on the nRF51822 Evaluation Kit, and I now need to port that into a module that sits on a custom board. Any recommendations for making this process...
Could someone can tell me what is the difference between BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME? I tried BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME
advertisement...
I am trying to figure out how interrupts are set up for say a sensor with an interrupt line which signals when new data is ready.
I am assuming you set up a GPIOTE somehow...
I have been looking at the NRF51822 for data logging sensor measurements from the ADC. Currently, I have run into some limitations with iOS and can only get approximately...
Hello,
Its me again.First of all I want to say thanks to HÅKON ALSETH, with his help I was able to work with hardware interrrupt. now I am facing another problem, I need...
want to FLASH upgrade FW in the nRF51822 though my application controller. Is C or C++ code available for this operation or can you deliver a protocol description how to setup...
Hello Everybody,
I am new to Nordic and Bluetooth. I see nrf51822a have BLE + Cortex MCU inbuilt and this suits best to my application.
I have some doubts regarding...
How do I use nRF51822DK without "nRFgo Starter Kit Motherboard"? I have read "nRF51822 Development Kit User Guide v1.2" and have no result how can I only use nRF51822DK hardware...
Dear All
i would like to use
nRF51822
nRF51422
i would like to use nordic product,
but so shame, too low basic knowledge for make program for embedded, edit library...
Hello,
I attached the schematic found in the manual for NRF8001, in the case of DC/DC converter enabled.
It shows that an external 32.768KHZ crystal is used, while in...
Hello, I have major problem trying to debug/run ble_app_hrs example. The thing is that when I enter debug mode the code is stuck here:
0x000001B4 4908 LDR r1,[pc,#32...
Based on nRF51822\Board\nrf6310\ble\ble_app_hids_mouse example,
Used hid consumer page function, like play/pause or volume+ or volume- ...etc function,
In nRF51822 device...
I can't seem to find the hex file to download into the PCA10000 in order to use it with the Master Control Panel. Where is this documented in the dev-kit documentation?
