hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
We are currently working on a custom modem firmware update. For this, we would like to use the CBO file you provided. Updating the segments with the CBO file is working so...
***Description***
I am trying to build a sample application which comprises of a notification from peripheral to central. I configured the PHY to 2M. With the mentioned...
I am trying to use Health SRV and Health CLI to check if there are any errors in the nodes. I have successfully transmitted the fault codes, but there are still many questions...
I have a battery operated unit & according to the data sheet I should be able to read the VDD pin
However, when I look in the nrf-saadc.h it does not have this listed...
Hi Nordic Team
We are developing products using the NORDIC NRF54L series chips, but we are encountering some hardware issues.
We have used the NRF52832-QFAA chip. Packaged...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
I am trying to make a simple MAC-layer transceiver using Arduino environment. I have some code derived from this example: https://github.com/IoTS-P/nRF52-802154-Raw-Transmitter...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
I am using nrf5340 audio DK,
The project I use is v3.0.2 .\samples\nrf5340\empty_app_core\. If the board target is nrf5340 audio DK
a compilation error will occur. build...
