I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
Dear Support Team,
I am currently working with two nRF54L15 DK boards placed approximately 50 cm apart and stationary. I am using the channel_sounding_ras_ example with...
I'm writing an application for the nRF54L15 that periodically receives the local time via bluetooth and keeps track of time on its own between syncs. I'm using a 10ppm external...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
We tried connecting a deeply discharged lithium-ion battery to the nPM1300-EK to see how it would charge, but we weren't allowed to enable charging as we got the following...
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
I have a single-ended signal that spans [0V,3.3V] and is centered around V_bias=1.65V (=3.3V/2).
I want to use the NRF54L internal gain to amplify only the AC parts of the...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi there,
i'm progrmming a Lcd over SPI but i got this failure once generate the build :
************************************************
* Executing task: nRF Connect...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
