Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
hey i want to make my device act as peripheral to smartphone at the same time act as boradcaster an to reach that we need gap_adv_type BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED...
I just received the nrf9160 DK and gone through nRF connect ( V3.3.0) installing toolchain, cloning the nRF Connect SDK and downloading Nordics version of SES
The problem...
Hi all,
We want to create some smart home networks based on BLE Mesh.
1. Is it possible to buy Nordic Thingy, load our software (temperature sensor based on BLE Mesh)...
Hi sir We have requirement Blutooth 5.0 for iot Appication. please can you share the schematic file
their is orcad capture design file or available or PDF file
Currently evaluating Bluetooth mesh and trying to use the Zephyr mesh_demo.
I added so that the instead of buttons triggering the bt_mesh_model_send from the main loop periodically...
now I'm on NRF24Le1 project, and I have a problem with wakeup TICK from timer or voltage level on pin (analog comparator wakeup). could you help me ? or have you an example...
Hi,
Is assisted GPS(AGPS) supported in nRF9160?
Our nrf9160 custom board takes 2 to 5 minutes for the first fix with active antenna. Does nrf9160 support AGPS data to...
Hi,
We recently purchased a thingy 52 for evaluation H/W 1.1.0 F/W 2.0.1
We are using an iPhone 8 with the latest Nordic apps.
When we connect using the the Thingy app...
I am new in nordic and just getting started with the nRF52832-DK. . Can someone please help me ? How to read 4 Digital Input and store it into SD card.and then pass that stored...
Hi,
I was using SDK 1.0.0 earlier.
I ported my code to new SDK v1.0.0.
But i am getting undeclared macro error as shown in below image
In prj.conf i have initialized...
Hi All,
I have arduino ble 33 ble device and able to connect with it using my android application using BLE library. I am trying to write 9000 or 18000 of UINT16 by converting...
hi ,,, i am getting the four data from various sensors, then i want to combine all the four data and send in ble_app in variable , example x=10;y=30;z=34 using sprintf i am...
Hi,
I want to use the nRF Mesh SDK on nRF52840 chip with proxy client role that can send messages over GATT connection to proxy server role device. Is that possible?
Currently...
Hi Nordic,
Chip set: nRF52840
SDK: 15.3.0
Softdevice: S140 (06.01.01)
Button interface with MCU: Total=13 (All with GPIOTE)
We have face one blocking issue at...
