Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
Description:
I am working on an application using the nRF9160 and encountered an issue where the #MQTTEVT event is not triggered after connecting to an MQTT broker using...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
Hey all,
I try to flash the SuperMini nRF52840 using my NRF52-DK over Debug HW (SWDIO pins). I try to flash the Zephyr blinky example.
I think I already got it (at least...
Hello,
I'm developing on a custom nRF5340 board without an external clock source - nRF Connect v.2.9.0. For my application, I'm using the internal system clock with this...
Hello,
I have made a PCB has 4 buttons and touchpad, now I want to drive all of them.
1. one button for left button of mouse. 2. one button for right button of mouse....
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Hi,
I am attempting to get Direct Test Mode working on my nRF54L15 while also having access to the normal BT stack.
Normally, if I run dtm_tr_init(), I can begin the test...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
Hello,
I have a custom nrf5340 board with an attached external RAM on the QSPI (I understand only NOR flash ICs are supported) on the older version of the SDK such as...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hello,
we would like to test our product after production. So I would like to connect a PC to the unit via BT-LE. My Idea was to use the nRF52840-Dongle like the nRF Connect...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
