I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello, how can i modify the hrs_s_evt_handler() to initiate bonding only if it my configured belt address?
My Solution:
static void hrs_c_evt_handler(ble_hrs_c_t * p_hrs_c...
Hello, All.
I want to know AppID in iPhone's App using ANCS.
(for example, Facebook App's AppID is "com.facebook.Facebook",
Facetime's AppID is "com.apple.facetime")...
Hi Nordics!
I want to add custom service into ANCS example for android.
But I cannot understand how to add custom service stably.
First, I just added my custom service...
I have compiled the nRF51-ble-bcast-mesh 's examples: "LED_mesh_SDK7" and "BLE_Gateway_SDK7" on Keil uVision v5.14.0.0. But, I am facing problems flashing them on to my nRF51422...
I have a problem that I can't figure out. I have a custom board with an nRF51822 QFAB. The board will run a test application that uses nrf_delay_ms() to toggle an output pin...
Hi!
I have reviewed the NRF518 reference design, i.e., case "PCB layout recommendations for the NRF51822 WLCSP62 package" and the layout pdf files provided therein:
...
Hi
I have read various things about this so I would like to confirm
What is the best way to set the bluetooth address of my device ? Is it built in by nordic ?
Or is it...
Hi,
I am able to change the MAC address of the beacon using the call sd_ble_gap_address_set(BLE_GAP_ADDR_CYCLE_MODE_NONE, &gap_addr), where gap_addr is of type BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
Hi, I am newbie at this field.
I have tried to configure network for communication between device nodes.
What i want to do is each device node has unique data( <30bytes...
Hi,
Is it possible to control the ouputs without connecting?
I mean something like this:
I have a nRF51DK. And I would like to detect if there are bluetooth devices...
I'm trying to get some sound out of a piezo buzzer using the PWM library here:
github.com/.../nrf51-pwm-library
My buzzer has a resonant frequency of 2,730Hz. The buzzer...
Hi all,
I am looking for some help on where to identify a problem that cropped up recently. I'm relatively new to the softdevice concept, though it seems straightforward...
Hey everyone,
I'm developing an application using the PCA10001 board. After a while my app crashes. I think this is due to un-freed memory regions. When writing similar...
