Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello,
I am designing a circuit using the nRF81522 chip.
I was wondering what should I do with the unused I/O pins.
Would it be OK to leave them unconnected, or there...
Hi
Could I use 3.3V to the C3 capacity in the application example,datasheet?That is to say,C3 doesn't connect to VDDPA pin and 3.3V connect to the C3.I found that it is...
We have developed our custom nRF8001 board and connected with Arduino UNO bord. we have used nRF HRM demo application from Github . We are using nRF utility application from...
OK, I didn't read enough fine print before I plunged in, but my version of the nrf51822 I have on a bunch of boards isn't supported by the new SDK.
In a premature onset...
I'm trying to use notifications with Android 4.4. When my service issues a call to sd_ble_gatts_hvx, the result is BLE_ERROR_GATTS_SYS_ATTR_MISSING.
From this link , I...
Hi
when i call twi_master_transfer function in for(;;) loop of file ble_app_hrs project.
Kindly tell me what to do for that.
for (;;)
{
for(i=0;i<10;i++)
{
...
When I plug the PCA10000 into my mac I can see it presents 3 USB interfaces. The first is interface class 0x02, Communication Control, the second is 0x0a, which is Communication...
Hello
I have problem to reach 100 feet and a high data rate using BLE.
I am thinking about using gazell. Is possible to communicate with gaxell protocol to IOS and Android...
Hi guys,
I am trying to get the maximum packet size out of my nrf24 radios. If I am implemeting my own radio protocol which doesnt require 3-5 bytes of address is it possible...
Note that nWP-018 "Migrating to the latest nRF51822 chip version" specifies that the SDK version which should be used with the Eval Kits I have (version 1.0, chip variant...
I'm using the nRF51822 with the version v5.2.1 S110 soft device and have implemented a communication scheme that is very nearly identical to the Nordic UART protocol as implemented...
Hi,
I'm currently working on an Android 4.3 app who must communicate with a model of a specific device.
This device contains a Bluetooth low energy chip nrf8001 and there...
Hi,
I have a problem when running 51822 with Nrf toolbox on android 4.3 Samsung S4. The problem is that the BluetoothGattServer disconnect itself after 30 seconds. The...
