Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I have a sample program that is failing on sd_ble_gap_device_name_set with an invalid parameter.
It's calling BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode)
And then it passes...
Gentlemen: Do you have posted a copy of the original firmware that comes installed on the nRF51822 beacon? I have been experimenting writing my own app on that beacon, and...
Hi all,
I have an TICK interrupt on RTC1 on nRF51822, but the program keeps cycling in the interrupt - as if the interrupt is never cleared?
Here's my code:
void...
Hello,
I am currently building up a little application on top of the ble_multilink_peripheral_example.
I would like to have the nRF Master Control Panel on Android to...
Hello,
First, my setup is as follows:
nRF51822 Rev. 3 dev board (PCA10028)
s110 7.1
SDK 6.1.0
I am developing firmware on the PCA10028. I am matching SPI to a custom...
Well not my best title. But I hope you can follow this explanation:
I added RTT to my project to replace UART. It works so far. But there is a strange behaviour...
Code...
I am trying to do OTA DFU on nRF51-DK from a BLE dongle (CSR 4.0) and gatttool from BlueZ. The image is compiled from blinky_s110_pca10028 example ( blinky_s110_pca10028.hex...
Hi
I want to program the S120 softdevice over an mbed HRM1017 ([link text] that uses nrf51822. I can program only with CMSIS-DAP or drag and drop over the drive. I am using...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hello,
as I couldn't manage to get my SPI Measurement working flawlessly when called from inside a timer handler I tried to work around it by just setting a flag inside...
Hi,
I have a setup :
nRF51822_QFAC Chip Rev3
Softdevice: S110 V8.0.0
SDK: V8
Code hangs at sd_softdevice_enable(). Clock Source I am using is NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hello,
Has anyone managed to get the Nordic_UART software to pair in Windows 8.1?
The heartrate monitor software pairs fine. Using show bluetooth devices, I can see the...
Hi,
I have a PCA10028 board. When I connect it to a computer the LED LD5 doesn't turn on at all, and no new USB connection pops-up in my computer. But when I connect it...
