hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi
Does the nrf-sw-pwm driver work on the nrf54l15. I am porting code form the nrf52840.
My output does not toggel, 0% and 100% does work but noting else.
I tried running the " Bluetooth: nRF Distance Measurement with Bluetooth LE discovery " case in the SDK, here is its link： Bluetooth: nRF Distance Measurement with Bluetooth...
Hello,
I'm trying to connect a BMI270 sensor over I2C using Port2 on the nRF54L15 , with the nRF54L15 DK , and I'm working with the nRF Connect SDK v2.9.0 , based on a Zephyr...
Hello,
I have the nRF7002 DK, which includes the nRF5340 (App + BLE cores) on-board.
The hardware requirements do not list this DK as usable for the course, which seems...
Hello,
I am currently designing with the nrf52840 and trying to implement the 32 MHz crystal required for bluetooth radio operation. The calculations for the load capacitance...
Hello,
I am attempting to build the Matter template using only the nRF54L15’s internal memory. While the build occasionally succeeds, it more often fails, and I am unsure...
The nRF52832 devices have been produced in hundreds of units. Currently, it has been found that individual central devices are problematic – connecting to peripherals often...
I have enabled all the dependencies asked as below
CONFIG_IMG_MANAGER =y
CONFIG_STREAM_FLASH =y
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_DFU_TARGET_MCUBOOT =y
Still...
I work for ChannelSounding on nRF54L15.(NCS3.0.1)
I measured the distance using two nRF54L15-DKs. The actual distance was 3m. The average measurement result is shown below...
I'm trying to use an ILI9341 display with nRF52840 in Zephyr (v4.1.99). The build fails with multiple errors about missing Devicetree properties when compiling display_ili9xxx...
Hi everyone, I'm working on a BLE connection between an nRF5340 DK (central) and an nRF52840 Dongle (peripheral), using NCS 2.9. Both devices are configured to use the CODED...
Hi Nordic Team,
I think I found an issue with the "Sysbuild domain settings" windows (in VSCode) use to set path for Kconfig fragment and overlay to parametrize mcuboot...
For the GetAssistanceData endpoint (POST /location/agnss), if we are using the x-custom-device-id header instead of a device token and registered devices, how can we view...
Hi, I'm new to nRF Connect, coming from the SDK. I'm building a Central/Peripheral system and I've got to the point where the Central is discovering what services and attributes...
