Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi Nordic Team,
I’m currently working on a project using the nRF54L series, and we are using a 32 MHz external crystal oscillator based on the reference design. On our PCB...
Description of the requirements
SDK:15.0.0
MCU:NRF52840
I currently have a product that is already in production, and I need to replace its boot program, and the new...
I am trying to flash a new board using a Segger J-Link Plus Compact. I use the same code to flash my nRF5340DK and it runs fine. I see the debug statements in the JLinkRTTViewer...
I'm working on a Thingy53 project with Zephyr RTOS that requires TLS connections, but I'm encountering persistent "Failed to create TLS socket: 23" errors (ENOMEM - out of...
Hi,
I'm trying to use the HCI UART sample to provide Bluetooth support through UART. At first I want to test it between two Nordic Boards, but later switch to another MCU...
Hi,
Also asked your AI, but if I combine the information on https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/measure_current_source_meter.html with that on https:...
Hello Community!
I want to use the npM1100 as a power management device in my project. The external battery to be used is the ER26500 and it is not rechargeable.
If I...
Hi,
We have a product in production which uses the mpsl_radio_notification_cfg_set() function along with a callback to control an external GPIO when thre is radio activity...
Hello, I have a question about how to monitor Zigbee devices for dead or alive, especially end devices that sleep. I am currently developing a hub to control and retrieve...
Hello, We have a custom board with nRF52832, using BLE, s132. I have noticed recently that in nRF Connect App (v4.29.1) usually the services and characteristics show up twice...
Hi there,
I am trying to develop a simple application that must write information within a micro SD card (nothing too fancy, it is just plain data read from the internal...
Hi,
I added MCUboot and SMP BT Service to the OpenThread CLI routine to implement the device firmware upgrade function.
I found that after DFU is completed, the Thread...
If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
Hi!
I cannot get I2S echo sample to work on nrf54L15. Tried following overlay
build configuration nrf54l15pdk_nrf54l15_cpuapp
I verified with oscilloscope that no...
Hi,
All-of-a-sudden I'm having problems debugging my application. THis morning it was working right, this afternoon it's gone wrong!
I think it's pretty near using up...
