I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi,
I'm using nRF51 Development Kit to program the beacons. I've connected the beacon just like it's described in the last update of this thread using the 10-pin adapter...
Hi,
I just noticed that the nrf51822 doesn't have an eeprom and I already had the pcbs done. Can I use the NVMC to write USER data on the CODE (is it flash memory are?...
I am trying to do over-the-air (OTA) device firmware update (DFU) on a device with bootloader same to the "dfu_dual_bank_ble_s110" example in the latest nRF51 SDK . On the...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
We are using Gazell to stream data at <=6mS intervals for very low latency wireless gaming peripherals. We'd like to have many of these peripherals devices (more than 24)...
Hello
I'm trying to get a SPI master onto my S210 programmed nRF51422. I'm using uVision 5 and have all the nordic packs installed and built off of the ant broadcast tx...
main.c
I am trying to talk to this sensor: www.meas-spec.com/.../MS5803-05BA.aspx via SPI... it quite seems to work as I get expected responses to commands but as the title...
Do the Nordic Boards offer some sort of config region where settings like the Bluetooth address are stored? I would like to change these settings without having to recompile...
I am trying to set up a GZLL star network on the 51822. I understand that a single GZLL host can support up to eight devices but whenever my host attempts to communicate with...
Hi Team,
Is there any example to understand Prepare Write Request/Prepare Write Response?
In ble_uart_app example, I am getting p_ble_evt->header.evt_id = 2 if I put...
I am using S110 v8, But I am having this problem since the very first stage of developement, so earlier versions of S110 also.
The problem is that sometimes I am advertising...
I'm running: SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.8.0.7
I'm trying to get Notifications to work. I have two attributes. I write to one and have it update the...
Hey I'm developing a sensor network using ANT shared channel. Here are my set up:
I'm using a Android tablet as master. The app was modified from aquired channel app...
I am able to connect see the buetooth NRf51822 ek on windows, iphone, but not mac, when I installed the ble_app_hrs app s110 8 on the ek board. Any idea?
